Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You may discover that your garage door opener has been giving you problems, so you need to repair it. You can fix it by changing a motherboard, a photo-eye sensing unit, the major drive gear, or the set-limit buttons. You can likewise inspect if the security sensors are working correctly.

Replacing a circuit board

Changing a motherboard for your garage door opener requires a few steps and tools. Initially, you need to shut off the breaker as well as detach any cables. Next, open up the motherboard cover. This will assist you to diagnose the trouble as well as identify if you need a new board. Next, get rid of the old board and its cord ports.

You can then proceed to change the circuit board. The substitute process is simple and also takes around 10 mins. A brand-new circuit board will set you back regarding $80. To protect your brand-new circuit board from power surges, you can acquire a rise guard.

Replacing a photo-eye sensing unit

Replacing a photo-eye sensing unit can be a relatively easy job. Initially, remove the sensing unit from the door and also see to it is positioned appropriately. If the sensing unit is angled by any means, it may not be obtaining the right signal, which can be causing the strobe lights. If you notice that the photo-eyes are out of positioning, you might need to have a specialist come as well as take care of the issue.

The photo-eye sensor contains 2 items that install outside of the door tracks and towards the flooring. The picture eyes will have a small LED light and also should be solid in shade. If the light is blinking, its most likely the photo-eye is malfunctioning and will need to be replaced.

Replacing a main drive gear

To change a garage door opener major drive equipment, beginning by eliminating the cap from the chain wheel. Next off, eliminate the two screws holding the drive equipment to the gear setting up. Currently, you can unfasten the three stress pins. Squeeze them from both sides and afterwards eliminate them. Then, separate the 3 cables from the garage door opener motor. These wires ought to be white, red, as well as blue.

Once you have gotten rid of the old gear, mount a new one. Be sure to grease it well. Insert the new equipment into the shaft, seeing to it to align the placing openings. Ensure the gear and also gear assembly are positioned properly to guarantee smooth operation. Next, make use of a hammer as well as a nail to drive a pin right into the new equipment.

Changing the set-limit switches

The first thing you need to do if your garage door is not functioning correctly is to check the set-limit switches. You may need to change them to make sure that the door shuts earlier or quits before it gets to the flooring. You can examine this by looking at your garage doors handbook or online.

To adjust the set-limit switches, youll need a screwdriver or outlet. Readjust the handle clockwise or counterclockwise till the door moves up and also stops, or decreases its range. To check for appropriate travel range, gauge the void from the bottom of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Key St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

One thought on “Veteran Garage Door Repair | Keller TX | 817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *